来宝网Logo

热门词:生物显微镜 水质分析仪 微波消解 荧光定量PCR 电化学工作站 生物安全柜

AED
现在位置首页>计量器具>表面测量器具>轮廓仪>现货Testex Press-O-Film副本卷带
现货Testex Press-O-Film副本卷带
现货Testex Press-O-Film副本卷带
  • 现货Testex Press-O-Film副本卷带

现货Testex Press-O-Film副本卷带

产品报价:询价

更新时间:2023/4/3 18:11:18

地:美国

牌:abqindustrial

号:Press-O-Film

厂商性质: 生产型,

公司名称: 世联博研(北京)科技有限公司

产品关键词: 副本卷带   Press-O-Film   abqindustrial   Testex   现货  

5162
访问人数
0
累计评论


王荣 : (18618101725) (18618101725)

(联系我时,请说明是在来宝网上看到的,谢谢!)


Testex Press-O-Film Replica Tape Rolls

Testex Press-O-Film副本卷带


Testex Press-O-Film Replica Tape Rolls
Testex Press-O-Film Replica Tape can be used with a Testex Micrometer or PosiTector RTR Replica Tape Reader to measure the surface roughness ("profile") of blast-cleaned steel.
Available in Grades Medium, Coarse Minus, Coarse, X-Coarse & X-Coarse Plus

Testex Press-O-Film Replica Tape offers a unique replica technique and with a simple Testex Micrometer or PosiTector RTR Replica Tape Reader will allow you to take accurate, low-cost blast-surface profile measurements. Testex Press-O-Film makes surface replicas easy to obtain and produces average maximum peak-to-valley readings that ensure optimum blasting effectiveness. Replicas can be retained for future needs.

The accuracy of Testex measurements is due to an innovative two-level film that can produce virtually exact replicas of the abrasive blast surfaces. The film is available in three different thickness grades to cover the most common range of blast profiles.

Measurements can be taken in locations that are not possible using conventional stylus devices, e.g. internal pipe diameters and grooves, etc.

Easy to use, remove the protective paper from the tape and place firmly on the blasted surface. Apply moderate pressure with the Burnishing Tool over the circular cut-out in the tape. Remove the tape.

The replica is now ready for measurement using the Snap Gauge. The Testex Tape is available in a Test Kit, comprising one roll of Coarse and one roll of X-Coarse Testex, Dial Thickness Gauge (specify metric or inch gauge), Training Surface, Burnishing Tool and instructions.

line
Testex Gauge
line

The Testex Gauge is used to measure the Testex Tape and determine the average maximum peak-to-valley height of the blasted profile.

Measurements are made by firstly zeroing the gauge on 50μm (2mils). This is to allow for the film backing. Place the replicated area between the anvils and gently lower the moveable anvil onto the film. The reading can now be taken, giving you the average peak-to-valley height of the blasted profile.

Supplied in a Carrying Case with Burnishing Tool.

The Testex Snap Gauge is available in a Test Kit, comprising 2 rolls of X coarse Testex (specify if you require other grades), Snap Gauge, Training Surface, Burnishing Tool and instructions.

line
Complies with International Standards
line

  • BS EN ISO 8503-5:2004

  • BS 7079-C5

  • SSPC-SP5, SP 6, SP 10, SP11-87T

  • ASTM D 4417-C

  • NACE RP 0287-95

  • ISO 8503-5

line
Specifications
line

Testex Press-O-Film replica tape is available in a variety of thicknesses to facilitate profile measurement in differing ranges:

Grade (descriptive)Range When Used With Gauge
(mils) / (microns)
Fine / Mediumnot applicable
Coarse Minus0.5 to 1.0 / 12 to 25
Coarse0.8 to 2.5 / 20 to 64
X-Coarse1.5 to 4.5 / 38 to 115
X-Coarse Plus4.6 to 5.0 / 117 to 127

现货Testex Press-O-Film副本卷带现货Testex Press-O-Film副本卷带现货Testex Press-O-Film副本卷带

世联博研(北京)科技有限公司

| 第14

手机:18618101725

联系人:王荣

电话:18618101725

传真:010-67529703

QQ:736597338

(联系我时,请说明是在来宝网上看到的,谢谢!)